Free Source of Wood Bowl Blanks From “Slabs” Cut By Portable Sawmills

Sawmills As A Free Source of Woodturning  and Bowl Blanks

I know there are a lot of people who turn wood and enjoy the hobby have a hard time finding wood.

That’s a little difficult for me to comprehend because we have so many trees that they fall on our houses, or in my case the garage/shop!

End grain sealing for woodturnersThere are a lot of good posts on where and how people find different sources of wood. How they collect it and how they process it.

I have one source of wood you might find interesting. There are many sawmills around the country/world large and small. There are many portable sawmills that will come up to your home or property and mill a tree into pieces that you tell them to. You can use these for construction or in our case, get them milled into sizes that we would want for bowl blanks or whatever you happen to turn.

portable bandsaw millHere’s a source I thought you might be interested in. Portable bandsaw mills are located around the country. You just have to find them. Search for sawmill, portable sawmill or contact any of the manufacturers and ask them if they have any of their mills in your area.

A portable bandsaw mill is basically a trailer with a gasoline powered bandsaw on it. A log is loaded on the trailer and positioned. The saw head is then lowered so the bandsaw blade can make a cut down the length of the log. The sawmill operator is looking to make a flat surface across the top of the log, it is then rotated and another cut is taken. This first cut is usually called a “slab” and this slab will have varying thickness.

This first piece or “slab” is usually worthless to everyone except perhaps for firewood. For woodturners, particularly “bowl turners” this first piece could be gold. Depending on how it is cut you might end up with blanks that could be ‘platters’ up to ‘bowls’. If you were able to convince a sawyer to add an inch or two to the first cut you would end up with as many bowl blanks as you can use since it runs the length of the log.

We had a guy come out and cut up some oak, cherry and poplar logs we had. Nobody wanted the slabs, I asked him to add a couple inches to the first cut and he thought I was crazy. But I ended up with 2 slabs that were 12′ or so long of Cherry. I then cut the slabs into 14″ pieces so I ended up with about 10 or 11 bowl blanks per slab.

bandsaw mill produces free wood bowl blanksThese ‘slabs’ as bowl blanks offer 2 types of bowls. You can turn live edge bowls or flip it around and you can cut some nice platters or bowls.

cutting bowl blank with bandsaw for free cherry bowl blanks from bandsaw millTake this one step further. One of my son’s purchased a bandsaw mill. It is a manual mill, hard work to load the load and then turn it while on the cutting rails. But….I can now cut that first piece any size I want!

Sawing wood is almost as addicting as turning wood. I suppose if I were younger and stronger I might want to a little more sawing 🙂 Keep in mind if you are interested in sawing wood, you can get a sawmill that is all hydraulic, no muscle required! But for the occaisional log here and there I can cut blanks for the next 10 years 🙂 Seriously, I started this article by talking about the first cut for bowl blanks because you can get those free from most sawyers. But if you had your own mill, or had someone come out and cut up a tree for you….. you can have the sawyer cut the log in slabs with the thickness that you desire.

I recently grabbed a cottonwood tree, actually about half the tree came down. I can now cut the slabs and then cut some middle pieces that are 6″ or more thick and then cut them in 12″ pieces that I will seal and stack for drying.

Slab Cut Into Bowl Blank Widths

Free Wood Bowl Blanks from portable bandsaw millThe picture shows the Cherry “slab” that I cut into 13 to 14″ pieces. The slab sat outside for about a year and was 15% to 20% moisture level. I should have immediately sealed the ends of those pieces but I didn’t. I just don’t have the energy or strenght to do too much anymore …..very depressing but that’s my life. I eventually did seal the ends to keep them from checking and cracking. I think I had about 10 bowl blanks.

Turning the Cherry Bowl Blanks

When turning bowls its nice to have the option of turning live edge bowls. The problem with live edge bowls is that the bark doesn’t stick and gets ripped off. I found this piece of cherry had some decent bark adhesion and it was possible to turn some shallow live edge bowls.

Free Cherry Bowl Blanks from local bandsaw millIf you try to turn live edge bowls and it almost never fails …..a piece of the bark will rip off and leave a space on the edge. You can sand and shape that edge or you can grab some of the bark and use some CA to glue the bark back on the edge of the bowl. Usually you need to use one of the 2″ sanding disks to shape and blend it into the existing bark …..but a little practice will make it look like it was never missing 🙂

Mounting The Slab Bowl
Blank on Your Lathe

Next would be to turn a bowl from the “slab” bowl blank by making the ‘flat’ side of the blank the top of the bowl. I usually will drill a 2-1/8″ hole   with a 2-1/8 inch forstner bit for the jaws of my Super Nova 2 Chuck (click here https://amzn.to/2JUGzXq)  and chuck up the flat face against the chuck with the jaws into the recess that I just drilled.

I will next shape the bottom of the bowl so that it looks like a bowl bottom. Normally the bark will fall off your bowl blank or you can pull it off easiy ….no so much with this piece. I read someplace how a turner would remove bark before putting it on the lathe, he used a small air powered chisel to pry and rip off the bark. So……first however I use a cheap harbor freight air powered chisel to take the bark off. The natural profile of the bottom is close to the profile of the bowl. So I will turn a tenon on the bottom of the bowl…..I like recesses but a tenon makes more sense since these ‘slabs’ are usually not too thick and a tenon helps to keep you from blowing through the bottom of the bowl.

I looked around for an air powered chisel and I think  I found you a better deal, you get 4 or 5 chisels instead of one and it costs less than $20. You’ll find yourself using this tool a lot but for our specific purpose it and easily strip the bark off a short piece of long in no time.

You ask, “Why do I need to strip off the bark. First let me say, if you are doing a live edge bowl then you might not want to use this tool. But if you are going to turn a bowl that doesn’t have any bark inclusions on in when finished ….this is what you want to use.

Of course you can leave the bark on and use your tools to cut through the bark and get down into the good wood. Unfortunately this is going to give you one hell of a ride. Some bark is attached to your bowl blank like the mountains of the Grand Canyon and other bark might be attached like the gentle rolling hills of the great planes.

Assuming you want to get rid of the bark so you can turn some wood, the bark has to come off. Embedded in the bark are stones, sand, and metal. You never know when stripping the bark will test you patience because your tools will become useless afterwards. I mean, you’re gonna have to go and sharpen them again so they might be cutting good again.

I can’t remember who turned me on to a small air hammer with a chisel to strip the bark from a bowl blank, or log …..but it has been a real blessing to be able to strip the bark off in a couple of minutes rather than using my hammer and chisel to clean the bark off a project whether it be bowl blank or small log. For 20 bucks you just can’t beat it and it might be one of the best wood-tuning investments you make 🙂

As I turn the tenon I will shape the bottom of the bowl/platter. Even if it is wet/green I will shape the bottom of the bowl and then take it through the progression of sanding from 80 grit to at least 240 grit or higher. This 2″ drill powered sanding disk is one of my favorites https://amzn.to/2JSk9WN 

I then flip the bowl around, attach it to the tenon and began to square off the front of the bowl. I usually will figure out how deep to take the bowl. Then I will attach a drill bit or forstner bit and drill a hole in the center to the maximum depth of the bowl. This keeps me from gouging out the bottom of the bowl and making a funnel 🙂

Since the “slab” usually isn’t too thick I usually forego keeping pressure on the bowl from the tail-stock. It makes for quick gouging and shaping of the inside of the bowl without fear of the bowl flying off the lathe. That is another reason I like using a tenon on these….. you can crank down on that tenon as hard as you can without damaging the tenon and feeling confident that the bowl will stay on your chuck.

So I finish he inside of the bowl with my Big Hurricane Scrapers   and then sand once again through a progression usually starting at 80 or 100 to 240 grit.

After sanding I will either finish the project or dry it. I use a couple different drying methods. If I think the water content is low I will set it on a shelf to dry. If I think it is over 20% moisture (use a moisture meter https://amzn.to/30UNIg9 or https://amzn.to/32V7xFQ ) I will put it in a bag of shavings and let it dry. Or…..my new technique is to put it in the microwave at 60 to 90 seconds. I’m still experimenting with the microwave treatment but I think I like it. You can literally and actually dry a piece within a 24 hour or less period of time and then mount it back up on the lathe ….sand it and apply your desired finish.

Wow!

All I wanted to do was tell you about portable sawmills and “slabs”. Sorry, got a little carried away but I hope you might find some if not all the info helpful.

For those of you who are having a hard time finding wood in your local area ….check out some of the local sawmill operators. Contact these guys ….they really are cool and enjoy doing what they do. If you have a relationship with one, when that tree comes down you might be able to get him to come out on the cheap. You also might be able to come out a job he is milling up ….make sure you give him a couple of bowls and you will have a source of wood for your tuning for a long time 🙂

If you haven’t checked out our facebook group, please do. Lots of good people there, lots of cool projects and if you have a question ….I’m sure you can get it answered. And if you are a woodturing pro or expert …..we can use your advice and you can help newbies out https://www.facebook.com/groups/woodturningbasics

Buy Wood Turning Blanks Online, How To Dry Wood Bowl Blanks, How To Make Wood Bowl Blanks, Large Wood Turning Bowl Blanks, Live Edge Wood Bowl Blanks, Round Wood Bowl Blanks, Wood Bowl Blanks, Wood Bowl Blanks For Sale, Wood Bowl Blanks For Woodturning, Wood Turning Blanks Sale, Wood Turning Bowl Blanks, Wood Turning Tool Blanks, Woodturning Ring Blanks